No Oil Deposits Mitsubishi Lancer Spark Plugs Through Hot - Pressing Assembly Line

Auto Spark Plugs Mitsubishi Colt Galant Lancer 2.0L 1.5L (1988-) MS851417

Product Description

1, Model No : DSP1022

2, OE NO / (Part number) : MS851417 / MS851178 / MS851237 / MS851187 / OE028 / BPR 5EA-11 / W 16 EPR11

3, Test capability : Salt Spray Test ,OK / High Temperature Endurance,OK

4, Power : Powerfull Withstand high temperature and high pressure

5, Inspection : 100% inspection

6, warranty : 1 Year / 50000 km

Assembly production

1, through the automatic powder machine, the amount of resistance powder (with Bosch the same supplier) + center electrode + screw + expansion powder into the finished ceramic insulator inside, after heating, the internal structure of the spark plug has been formed.

2, after forming the need for internal voltage test, after 25000V high voltage on each of the detection of whether the breakdown of insulation and leakage, excluding unqualified products.

3, through the hot-pressing assembly line, the insulator and iron shell welding. And we are using hot riveting welding technology, this technology is currently Bosch's spark plug is also being used. Because the welding is the need for heating, so in the hexagonal screw will be under a circle of light blue halo. The NGK is the use of cold riveting technology, so the insulator and iron shell where there will be a small layer of pale white powder.

4, after assembly into the finished product, will be simulated air pressure detection, simulation of the engine cylinder operating pressure, the finished product installed into the test center electrode and the distance between the side of the electrode to achieve the ignition requirements of the engine to detect its performance and quality.

5, the detection of quality problems of finished products, for packaging.

Fit Model

Maintenance analysis

1, the normal working conditions: the top of the insulator was light brown, no fuel or oil deposits.

2, carbon deposition: the surface of the black sediment, indicating that the mixed gas is too thick, weak ignition or calorific value is too low. So it is recommended to check the fuel and ignition system of the engine before replacing it.

3, the electrode burned: the calorific value is not correct, or the mixture is too thin or too early ignition time, waste recycling system and the ignition line of mutual inductance may lead to early ignition.

4, the engine jitter analysis: * Idle jitter 1, intake manifold or more valve leakage; 2, throttle and inlet fouling too much; 3, idling control element failure; 4, nozzle clogging or sealing bad ; 5, ignition coil high-voltage line aging failure; 6, spark plug leakage, coke, the gap is too large. 3, the transmission shaft bending deformation; 4, oil blockage, poor oil; 5, the valve damage, cylinder pressure uneven. 2, the tire pressure is not balanced; 3, 4, the ignition coil energy is insufficient; 5, the spark plug is attached to the oil dirt, gap fire, and the fire is not enough, * Occasional flameout 1, poor fuel supply, fuel injector or oil block; 2, the sensor failure; 3, motor failure.

Engine knocking phenomenon

Engine knock is an engine abnormal combustion (overheating combustion) phenomenon, knock is usually very serious, if it is in high-speed high-load continuous and serious knock, not a minute, Spark plug and piston melting, serious even the cylinder and the engine body will be blown wear. There are six reasons: Ignition time premature - Ignition is too early, means that the piston before the deadline to establish the pressure, will hinder the piston rise, lack of power, because the piston to overcome the resistance to reach and cross the top deadline. It is possible in the intake valve is not completely closed when the combustion gas poured into the intake pipe burning, called temper, but also very scary. So to adjust the ignition time. The engine there is a serious carbon deposition - fuel or oil quality is not good, so that burning is not good, resulting in excessive carbon deposition, so to clean up the engine in time. Air-fuel ratio (A / F) is too low - air-fuel ratio, which represents the mixing ratio of air and fuel. Air-fuel ratio is an important parameter when the engine is running, it has a great impact on the exhaust emissions, the engine's power and economy, and this should check the oxygen sensor first. Cooling and cooling system work poor - cooling water due to leakage, infiltration or evaporation and reduce the natural heat away from the body will be reduced, so that the engine accumulated heat too much. The same heat sink device will make the engine heat load is too large, but also make the engine knock, timely inspection of cooling water, heat sink. Turbocharged vehicle turbines are pressurized high - turbocharged in general will allow the temperature of the front cabin to be higher and adjust the turbine pressure control device. Do not tighten the spark plug - according to the torque requirements to install the spark plug, if the spark plug did not tighten, will leak combustion gas, loss of power at the same time will lead to early ignition, causing knocking phenomenon. When this happens, remove the spark plug and observe the gasket. To determine whether our spark plug tightened, it depends on whether the sealing gasket pressure down

FAQ (Fluently Asked Questions)

Q1. If we don't find the model type here, Please tell us.

1, Please send us your OEM number.

2, Please send us your photo and products size if you have.

3, Please tell us your exact car model if you do not have photo or OEM number.

Q2. What is your sample policy?
1, We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.

Q3. Do you test all your goods before delivery?
1, Yes, we have 100% test before delivery.

Q4. What is your terms of payment?
1, T/T 30% as deposit, and 70% before delivery. We'll show you the photos of the products and packages before you pay the balance.

  Shanghai Hongshi Mechanical Co., Ltd is the production of auto parts as the main product of the enterprise. In order to facilitate the export of goods and the reception of customers, the board of directors decided to set up a professional sales company. So the Shanghai Hongshi Mechanical Co., Ltd was founded in Shanghai in 2015. Our company own 5 factories and cooperate with 13 factories. The factory covers an area of 200 thousand square meters, mainly in Anhui, Jiangsu, Zhejiang, Shandong, Hebei provinces. The main products: ignition coil, spark plug, spark plug, nozzle, filter, solar term door, fuel pump, brake, starter, engine, compressor, blower control module and other auto parts. We have the ability to provide customers with mass production and diversity.

  Our factories have professional professors, senior engineers and other technical personnel, and constantly research and develop the new materials, more durable, safer products. The structure is more optimized and the cost is lower. Enjoy a high reputation in the industry.

  Our factories has advanced equipment of production, such as: high precision sealing machine imported from Germany (brand name: Heydrich), high speed automatic winding machine from Japan, all kinds of equipment of testing and application by homemade, fully automated assembly line production, advanced casting equipment, cold extrusion equipment, high-precision CNC processing equipment, and advanced ceramic manufacturing equipment. Provide a strong guarantee for the quality of our products and our reputation.

  Our products manufactured by the factory are strictly inspected by the quality department before they can be sent to the customer. The quality engineers conduct a rigorous inspection of the raw material and process of the product. Conduct effective testing of products using various simulated laboratory equipment to make sure the product safely and durably.

  Our current dozens of types of products are exported to North America, South America, Europe, Asia and part of Africa. In 2016, our customers were satisfied with our products and services by 98%. We will continue to strive to provide customers with better products and services.

The pursuit of customer satisfaction is the eternal goal of every employee of Xineng. For those who use our accessories, happy travel, safe home. It is the target of fine production for our staff.